Memoq MR-720 Manual de usuario Pagina 15
- Pagina / 109
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
SR715/720 LCR METER
xiii
COMMAND LIST
VARIABLES i,j Integers
x Real Number
MEASUREMENT SETUP
$STL(?) {i} Set (query) settling time to between i=2 and i=99 milliseconds.
AVGM(?) {i} Set (query) averaging on (i=1) or off (i=0).
BIAS(?) {i} Set (query) DC bias to internal (i=1), external (i=2), or off (i=0).
CIRC(?) {i} Set (query) equivalent circuit to series (i=0) or parallel(i=1).
CONV(?) {i} Set (query) constant voltage mode on (i=1) or off (i=0).
FREQ(?) {i} Set (query) drive frequency to 100Hz(0), 120Hz(1), 1kHz(2), 10kHz(3) or 100kHz(4).
MMOD(?) {i} Set (query) measurement mode to continuous (i=0) or triggered (i=1).
NAVG(?) {i} Set (query) number of measurements to be averaged from i=2 to i=10.
PMOD(?) {i} Set (query) parameter mode to Auto(0), R+Q(1), L+Q(2), C+D(3), or C+R(4).
RATE(?) {i} Set (query) measurement rate to Fast(0), Medium(1) or Slow(2).
RNGE(?) {i} Set (query) measurement range to 100kΩ(0), 6.4kΩ(1), 400Ω,(2) or 25Ω(3).
RNGH(?) {i} Set (query) range hold to enabled (i=1) or disabled (i=0).
VOLT(?) {x} Set (query) drive voltage to 0.1V ≤ x ≤ 1.00V with 0.05V resolution.
MEASUREMENT CONTROL
PREL(?) {x} Set (query) nominal parameter value for deviation and %deviation to x (Ω,F,H).
STRT Starts a measurement.
STOP Stops the current measurement.
*TRG Same as STRT.
MEASUREMENT RESULT
OUTF(?) {i} Set (query) the output format to verbose (0) or concise (1) ASCII, or verbose (2) or
concise (2) binary.
XALL? Returns major and minor parameters plus bin number.
XBIN? Returns bin number of current measurement.
XDLT? Returns deviation between major parameter and nominal value.
XMAJ? Returns value of the major parameter.
XMIN? Returns value of the minor parameter.
XPCT? Returns percent deviation between major parameter and nominal value.
BINNING
BCLR Clears nominal values and limits for all bins. All bins are closed.
BING(?) {i} Set (query) binning to enabled (i=1) or disabled (i=0).
BLIM(?) i,j {,x} Set (query) upper (i=0) or lower (i=1) limit of bin j (0-7) to x%.
BNOM(?) i {,x} Set nominal value of bin i to x.
SETUP CONTROL
*IDN? Returns the SR715/720 identification string.
*OPC(?) Set bit in Standard Event Status byte when measurement complete.
*RCL i Recall setting i.
*RST Reset unit to default configuration.
*SAV i Save current setup as setting i.
*WAI Wait until all measurements are completed before proceeding.
STATUS
*CLS Clear all status registers.
*ESE(?) {i} Set (query) the Standard Event Status Byte Enable register to value i (0-255).
*ESR? {i} Query Standard Status byte. If i is included, only bit i is queried.
*PSC(?) {i} Set (query) power-on status clear bit to clear (i=1) or maintain (i=0) status values.
*SRE(?) {i} Set (query) the Serial Poll Enable register to value i (0-255).
- Model SR715 1
- Model SR720 1
- LCR Meters 1
- TABLE OF CONTENTS 3
- SR715/720 LCR METER 10
- SR715/720 LCR METERS 18
- GETTING STARTED 19
- GETTING STARTED 20
- OPERATION 24
- TEST CONDITIONS 27
- CONNECTING A DEVICE 35
- Binning Worksheet 44
- ACCURACY 47
- ACCURACY 48
- REMOTE PROGRAMMING 55
- REMOTE PROGRAMMING 56
- PERFORMANCE TESTS 76
- PERFORMANCE TESTS 77
- CALIBRATION 85
- CALIBRATION 86
- TROUBLESHOOTING 90
- TROUBLESHOOTING 91
- MAINETENANCE 94
- MAINTENANCE 95
- SR715/720 PARTS LIST 100
Philips 15PT2967/05 Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Fernseher & Monitore Philips 15PT2967/05.
Wir stellen 1 PDF-Handbücher Philips 15PT2967/05 zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Comentarios a estos manuales